warranty warranty

Operating Instructions

The PEET Dryer is designed for easy use and long service. When you follow these simple instructions and guidelines, the PEET Dryer will dry your footwear or gear safely and efficiently. Drying time depends on material and saturation.

Operating Instructions for:

Please note that these Operating Instructions are provided only as a convenience to our customers. For Operating Instructions that accurately describe correct product usage to meet warranty compliance, please refer to the printed Operating Instructions that came packaged with your specific PEET Dryer product.

Original PEET® Dryer (M97)
and Multi PEET® Dryer (M06)

  1. Assemble the Original PEET Dryer base by sliding together the base plates. (The Multi PEET Dryer base does not require assembly).
  2. Secure the standard equipment Footwear DryPorts onto the PEET AirChamber tubes.
  3. Place your footwear upside down over the Footwear DryPorts. Make sure the toe is higher than the heel so that the footwear will dry thoroughly. Loosen tongue and laces for a loose fit between the footwear and the AirChambers. This will allow air to circulate properly.
  4. To turn on the PEET Dryer, simply plug it in.

The PEET Dryer will get warm, reaching its maximum temperature in 10 minutes, but it does not get hot. This product uses natural thermal convection technology; there are no fans or moving parts, therefore it will not blow hot air or make noise.

The PEET Dryer can dry footwear without damage to any type of material. Footwear and gear can be washed first, or simply dried on the PEET Dryer after wearing.

IMPORTANT NOTES:

KEEP AIR VENTS AT THE BACK OF THE BASE FREE OF OBSTRUCTION.
THERE MUST BE AT LEAST 6 INCHES OF CLEARANCE BETWEEN THE TOP OF THE FOOTWEAR AND THE BASE OF THE DRYER. This will allow the warm air to move freely for proper drying.

DO NOT PLACE FOOTWEAR OR GEAR DIRECTLY ONTO THE AIRCHAMBER TUBES, WITHOUT DRYPORT ATTACHMENTS. The patented PEET DryPorts are designed to circulate the warm air through footwear, minimizing drying time and maximizing effectiveness. Failing to use DryPort attachments blocks proper air circulation, limiting the dryer’s ability to move air freely and may cause the product to overheat.

DO NOT PLACE THE PEET DRYER CLOSE TO A SECOND HEAT SOURCE, such as a furnace register.

Top

Advantage PEET® Dryer (M07)

  1. Attach the standard equipment Footwear DryPorts onto the PEET AirChamber tubes.
  2. Plug fan unit into outlet.
  3. Locate the switch that indicates the choice of using heated air or room temperature air. Move the switch to the desired setting.
  4. Rotate dial to select desired length of time for drying. Maximum time is 180 minutes or three hours. Time is displayed on the LED readout and will count down until time expires, when the unit will automatically shut off.

PEET® Pure: This product uses ionization technology, which will remain functional whether the dryer is operating with or without heat. Ionization technology arrests bacteria growth and precipitates many airborne contaminants including pollen, dust and dust mites, viruses, animal dander, odors and toxic chemical fumes — most of which contain positive ions. Ionization technology produces negative ions, which are drawn to positive ions. The negative ions weigh down the contaminant particles, causing them to become too heavy to remain airborne. As a result, the contaminants will drop out of the air or, in this case, out of your footwear or gear.

IMPORTANT NOTES:

KEEP AIR VENTS AT THE BACK OF THE BASE FREE OF OBSTRUCTION.
THERE MUST BE AT LEAST 6 INCHES OF CLEARANCE BETWEEN THE TOP OF THE FOOTWEAR AND THE BASE OF THE DRYER. This will allow the warm air to move freely for proper drying.

DO NOT PLACE FOOTWEAR OR GEAR DIRECTLY ONTO THE AIRCHAMBER TUBES, WITHOUT DRYPORT ATTACHMENTS. The patented PEET DryPorts are designed to circulate the warm air through footwear, minimizing drying time and maximizing effectiveness. Failing to use DryPort attachments blocks proper air circulation, limiting the dryer’s ability to move air freely and may cause the product to overheat.

DO NOT PLACE THE PEET DRYER CLOSE TO A SECOND HEAT SOURCE, such as a furnace register.

Top

Go! PEET® Dryer (M04)

What is included:

  • One pair of Portable PEET Dryers
  • Transformer plug for standard household electrical outlets
  • 12 volt adapter plug for standard automobile, RV or boat outlets
  • PEET® Pouch for travel
  1. Open each dryer and place inside footwear with DC jack upward.
  2. Plug the transformer or 12 volt adapter into the DC jacks on the dryers.
  3. To turn on the Go! PEET Dryers, simply plug the transformer or adapter into an appropriate outlet.
  4. Loosen the tongue and laces of footwear for a loose fit between the footwear and dryer. This will allow air to circulate properly and dry more effectively.

The Go! PEET Dryers will get warm, reaching their maximum temperature in 10 minutes, but they do not get hot. This product uses natural thermal convection technology; there are no fans or moving parts, therefore it will not blow hot air or make noise.

The Go! PEET Dryers can safely be left plugged in and in your footwear overnight or until you are ready to wear them again, without any harm to the product.

PEET® UV: The Go! PEET Dryer uses ultraviolet (UV) light technology to break organic molecular bonds found in germs, viruses, bacteria, fungi (like molds), etc. No other air purification is more effective at neutralizing microorganisms than UV light. This component of sunlight is the main reason that microorganisms die when left exposed outdoors.

PEET® Safe: The Go! PEET Dryer uses Positive Temperature Coefficient (PTC) heating technology to assure safety. PCT heating elements are small ceramic stones with self-limiting temperature characteristics. PTC stones are energy efficient, and have fast heating response times that plateau once the pre-defined reference temperature is reached. This technology has been installed and set to a predetermined temperature that maximizes the effectiveness of the dryer and will not allow it to overheat.

IMPORTANT NOTE:

ALWAYS USE DRYERS IN OPEN POSITION. Closed position is for travel only.

 

Top

Hydration PEET® Dryer

For drying personal hydration systems

Assembly Instructions
The personal hydration bladders should not have liquids still in them when placing them on the Hydration PEET® Dryer. The dryer is designed to effectively remove residue liquid that’s left behind to prevent the growth of mold and mildew.

1.  Place Base & AirChamber on flat surface

2.  Fit Water Exhaust Elbowpiece over the opening of the AirChamber

3.  Attach DryPort & Nosepiece over the opening of the straight part of the Elbowpiece

To Use
 

  • Plug in to a household outlet. CAUTION: To prevent electric shock match wide blade of plug to wide slot and fully insert. If the plug does not fit fully in the outlet, reverse the plug. If it does not fit, contact a qualified electrician. Do not modify the plug in any way.
    ATTENTION: Pour éviter les chocs électriques, introduire la lame la plus large de la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu‘au fond.
  • Place personal hydration bladder/reservoir over the Dryport & Nosepiece.
  • For smaller bladders slide the Nosepiece off the DryPort. Press down on
    the trigger and slide the banner over the DryPort making sure that the sides of the bladder are not touching it. Release trigger.

    Hydration PEET safely and quietly dries ladders/reservoirs in 2-3 hours.

 

Top

SafeKeeping PEET® Dryer Installing & Operating Instructions


Dryer Placement
 

  • Place the dryer in the corner of the safe or cabinet.  IMPORTANT: The dryer must always be used with the AirChamber (center tube) in the upright vertical position.
  • Place or mount the dryer into the floor or base of the safe or cabinet – never to the sides or ceilings.
  • If desired the dryer can be fastened to the base surface. Insert screws into the holes on the dryer’s base and secure. (Insert screws into the safe’s padding – not into the metal.)
  • Route cord through your safe wall or cabinet base. (Refer to Electrical Cord Installation on other side of this page.)

Operating Instructions

  • Always keep base air vents free of obstruction.
  • Always operate with the AirChamber (center tube) in the upright vertical position, with the dryer placed on the floor or base of the safe or cabinet – never the sides or ceilings.
  • Plug into a household outlet. CAUTION: To prevent electric shock match wide blade of plug to wide slot and fully insert.
  • If the plug does not fit fully in the outlet, reverse the plug. If it does not fit, contact a qualified electrician. Do not modify the plug in any way.

ATTENTION: Pour éviter les chocs électriques, introduire la lame la plus large de la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu‘ au fond.

Electrical Cord Installation
 

The following details how to remove the plug housing and prongs so that the electrical cord can be fed through the wall of the safe or cabinet.

There are three components (See illustration 1):

A. The electrical cord
B. The plastic plug housing
C. The prongs/holder

Make sure your hands are clean and dry.


1. Using the thumb and first finger on your dominant hand, grab the prongs. While squeezing them tightly together, grab the plug housing firmly between the thumb and first finger of your other hand. Firmly slide the housing away from the prongs. (See illustration 2)

2. Fold down both prongs away from their holder until you feel resistance and remove electrical cord. Slide the plug housing off the cord. (See illustration 3)

3. Feed the cord through the wall of the safe or cabinet.

4. Replace the plug housing onto the cord, and with prongs still in their spread position, push the cord into the prong holder until it bottoms out.

5. Squeeze the prongs back together. Holding them firmly, slide the plug housing back over the prong holder until the holder is flush with the base of the housing.

6. Straighten prongs to their plug-in position.

Top

Peet Propane Shoe Dryer - Model# P2000-B

 

  • Made in the USA
  • Safely dries footwear in 3 to 6 hours, (remove footwear when done drying.)

         A 16oz propane cylinder will operate the dryer for over 40 hours (propane cylinder not included with dryer.)

  • Fully portable/ will break down for easy transport
  • One year warranty/ 30 day money back guarantee
  • For OUTDOOR use only

LIGHTING INSTRUCTIONS:

1.  Open valve one turn.
2.  Purge fuel line for 30 seconds to remove air from line.
3.  Lay dryer on its side to light.
4.  Use match to ignite fuel at the hole in the middle tee.
5.  If ignition doesn’t occur within 2-3 attempts, place thumb over large hole directly behind retaining washer and relight.  Once lit leave thumb over hole until heater warms up (15 –30 seconds.)
6.  Once lit there will be a small blue flame in the center tee (difficult to see in bright sunlight.)
7.  Stand dryer upright on flat level surface for operation.
  

SPECIFICATIONS:                                               

Propane min BTU 200 Max BTU 450

Regulator by PRECIMEX

CSA  3.00   U.S.

DO NOT CONNECT TO A REMOTE GAS SUPPLY

 

Top

Warnings:

Regarding your PEET® Dry Warranty: Failing to follow the Operating Instructions enclosed with your PEET Dryer product may cause your dryer to overheat, resulting in damage to the dryer and/or your footwear or other gear.

FAILING TO
FOLLOW THESE INSTRUCTIONS AND WARNINGS WILL VOID YOUR WARRANTY.

Regarding PEET® DryPorts: Always use the appropriate PEET DryPort attachments for the type of gear you are drying. If these accessories are not available from the retailer where you purchased your PEET Dryer, you can order PEET DryPorts online.

Regarding PEET® AirChamber Extensions: Always use the correct PEET Extensions as directed, when drying footwear over 10 inches in height, such as taller style boots, waders or footed dry suits. Use 6-inch extensions for knee boots; 12-inch extensions for hip boots; 2 pair of 12-inch extensions for chest waders or dry suits. If these accessories are not available from the retailer where you purchased your PEET Dryer, you can order PEET Extensions online.

There must be at least 6 inches of clearance between the top of the footwear and the base of the dryer. (See illustration below).

CORRECT

INCORRECT
(No DryPorts; not
enough clearance)

Regarding Go! PEET® Dryers: Always use the Go! PEET Dryers in the open position. (See illustration below).

CORRECT
(Open)

INCORRECT
(Closed)

 

© Copyright 2007 PEET Shoe Dryer, Inc.

warranty